Home - Return to Previous Page
Additional Images

Racing Beat Header for 1990-1993 Mazda Miata

1.6L Miata Header

23993622 - 56005
  • Fits 1990-1993 Mazda Miata - 1.6L engine - Manual Transmission only
  • Manufactured entirely from 304-stainless steel for superior durability
  • Cast stainless steel engine-to-header and header-to-mid pipe flanges
  • 4:1 Miata header design
  • 1.5" OD tubing has been used for the primary tubing, and then collects into the 2.0" OD secondary
  • Downstream header-mid-pipe gasket included. Reuse OEM gasket at the head
  • Availability: Delays possible due to manufacturing times or vendor availability
    Shipping: Flat Rate Shipping $100 (does not apply to AK and HI)
    Pricing: $552.09
    Qty:

    Description

    Racing Beat Headers for the 1990-1993 Miata (manual transmission only) are the result of exhaustive research and engineering efforts, utilizing both chassis dynamometer and road testing. Our Racing Beat headers incorporate a tuned 4-to-1 design configuration to optimize exhaust gas scavenging characteristics and power output, while improving both the exhaust note and retaining the factory catalytic converter. Hundreds of development hours and over 200 on-chassis dyno runs were used in the refinement of this header. The Racing Beat header has been design-tuned to provide measurable horsepower and torque improvements throughout he entire RPM range. Manufactured entirely from 304-stainless steel for superior durability, this 4:1 header will offer years of enthusiastic performance driving. Exclusive cast stainless steel engine-to-header flange features specially designed exhaust ports which transitions smoothly to the primary tubing. For the 1.6 liter Miata engine our header utilizes large diameter 1.5" OD tubing for the primary tubing, and then collects into 2.0" OD secondary tubing. All emissions control devices are retained. Each Miata header kit comes complete with installation instructions and replacement rear gasket. If needed, a header-to-engine gaskets can be ordered separately.

    Header Development

    During the summer of 2002, Racing Beat undertook a significant project to upgrade their Miata header line. The scope of the project was to produce a 4-1 (four into one) type header for the 1.6 liter Miata and compare it against the power characteristics of our then current 4-2-1 (Tri-Y) type header. The new prototype headers would feature a new engine-to-header flange, collector, and outlet flange. They also took the opportunity to change construction materials from mild-steel to 304-stainless steel. With the new 4:1 header project, their initial performance objective was to retain the mid-range performance (3,000-5,000 RPM) of the then current 4-2-1 (Tri-Y) header, and improve the top-end performance (5,000-7,000 RPM) normally associated with the 4:1 type header. Under the guidance of Jim Mederer, Racing Beat's co-founder and chief engineer, initial testing on this project took place almost entirely on the chassis dyno. A rather strange looking test header was configured that allowed us to actually change the primary and/or secondary lengths while the car was strapped to the dyno. This entire assembly was suspended over the car by a specially built frame. Over 200 on-chassis dyno runs allowed them to determine the optimum tubing diameters and lengths for both the primary and secondary tubes. They also took the opportunity to experiment with various engine-to-header flange porting configurations and collector designs. This development allowed them to fine-tune the performance of this new header to achieve their performance requirements. After repeated test sessions, they finally found the optimal combination that allowed us to achieve their target goal. The test results showed that the top end power of their 4:1 header had improved and the mid-range power was retained.

    Details

    • 23993622 - 56005
    • 23993622
    • 56005
    • Racing Beat
    • Delays possible due to manufacturing times or vendor availability
    • New

    Shipping Information

    • Item Requires Shipping
    • 15.0 lbs.
    • W20.0000” x H10.0000” x L40.0000”
    • $100.00
    • Flat Rate Shipping $100 (does not apply to AK and HI)

    Customer Reviews

    Comment Total Reviews (0)

    Write the First Review!

    You must login to post a review.